Veteran Garage Door Repair | Keller TX | 817-769-8488

Veteran Garage Door Repair | Keller TX | 817-769-8488

Garage Door Opener Repair

You might locate that your garage door opener has actually been giving you troubles, so you require to repair it. You can repair it by changing a circuit card, a photo-eye sensing unit, the main drive gear, or the set-limit buttons. You can also inspect if the safety and security sensors are functioning appropriately.

Replacing a motherboard

Replacing a circuit board for your garage door opener needs a few steps and tools. Initially, you need to switch off the circuit breaker and also disconnect any kind of cables. Next off, open the circuit board cover. This will assist you to detect the problem as well as figure out if you require a new board. Next off, eliminate the old board and also its cord connectors.

You can then continue to change the circuit board. The substitute procedure is very easy and takes about 10 minutes. A brand-new circuit board will set you back about $80. To shield your new circuit board from power surges, you can purchase a surge guard.

Replacing a photo-eye sensor

Changing a photo-eye sensing unit can be a rather straightforward job. First, get rid of the sensing unit from the door and make certain it is positioned appropriately. If the sensing unit is angled by any means, it might not be receiving the correct signal, which might be creating the strobe lights. If you notice that the photo-eyes run out alignment, you might require to have a specialist come and also take care of the problem.

The photo-eye sensing unit includes 2 items that place on the outside of the door tracks and toward the floor. The image eyes will certainly have a little LED light and also must be solid in color. If the light is blinking, its likely the photo-eye is defective and also will require to be replaced.

Changing a main drive gear

To replace a garage door opener major drive gear, beginning by eliminating the cap from the chain pulley-block. Next off, get rid of both screws holding the drive equipment to the gear setting up. Currently, you can loosen the 3 tension pins. Press them from both sides and after that remove them. After that, detach the 3 cords from the garage door opener electric motor. These wires should be white, red, and also blue.

As soon as you have removed the old equipment, install a new one. Be sure to grease it well. Put the new gear into the shaft, seeing to it to align the placing openings. See to it the equipment and gear assembly are positioned properly to make certain smooth operation. Next off, utilize a hammer and a nail to drive a pin into the new gear.

Changing the set-limit switches

The initial thing you need to do if your garage door is not working correctly is to inspect the set-limit switches. You may need to readjust them so that the door shuts earlier or quits prior to it reaches the flooring. You can examine this by taking a look at your garage doors handbook or online.

To adjust the set-limit switches, youll require a screwdriver or socket. Readjust the handle clockwise or counterclockwise up until the door goes up and also quits, or reduces its range. To check for proper traveling range, measure the gap from the bottom of the garage door to the ground.

Veteran Garage Door Repair – Keller

204 S Main St Ste 105, Keller, TX 76248, USA

817-769-8488

https://veterangaragedoor.com/veteran-garage-door-repair-of-keller-tx/


Garage Door Repair


Garage Door Installation


Garage Door Company


Garage Door Service


Garage Door Opener Repair

Veteran Garage Door Repair | Keller TX | 817-769-8488 Veteran Garage Door Repair | Keller TX | 817-769-8488 Veteran Garage Door Repair | Keller TX | 817-769-8488 Veteran Garage Door Repair | Keller TX | 817-769-8488 Veteran Garage Door Repair | Keller TX | 817-769-8488
Veteran Garage Door Repair

204 S Main St Ste 105
Keller,TX
76248
817-769-8488

Leave a Reply

Your email address will not be published. Required fields are marked *